鋁板存放：應存放在干燥通風的地方，并平放在表面，不要踩踏、撞擊。

Aluminum plate storage: It should be stored in a dry and ventilated place, and placed flat on the surface, without stepping or hitting.

鋁板搬運：板的四周應同時抬起，以免劃傷板的表面。

Aluminum plate handling: The edges of the plate should be lifted simultaneously to avoid scratching the surface of the plate.

鋁板切槽：用插床或鑼機切槽時，應使用半圓頭銑刀。無論對鋁板的損傷是否太深，也不太淺，不易折疊，0.2-0.3mm厚的塑料芯應與鋁板一起彎曲，以增加強度和韌性，否則鋁板彎曲時可能斷裂或漆膜破裂。

Aluminum plate groove cutting: When using a slotting machine or gong machine to cut grooves, a semi-circular end milling cutter should be used. Regardless of whether the damage to the aluminum plate is too deep, not too shallow, and not easy to fold, plastic cores with a thickness of 0.2-0.3mm should be bent together with the aluminum plate to increase strength and toughness, otherwise the aluminum plate may break or the paint film may break when bent.

鋁板彎曲：彎曲邊緣時，應力均勻，成型一次，不要反復彎曲，否則鋁板可能斷裂。

Aluminum plate bending: When bending the edges, the stress should be uniform and formed once. Do not bend repeatedly, otherwise the aluminum plate may break.

鋁板電弧加工：應采用專用彎曲設備對電弧進行加工，使板材逐漸達到所需的表面，不得一次彎曲。

Aluminum plate arc processing: Special bending equipment should be used to process the arc, so that the plate gradually reaches the required surface and cannot be bent in one go.

鋁板批次：同一類型不同批次的鋁板可能存在色差。在銷售和使用不同批次的紙張時，應增加色差比較程序。

Aluminum plate batch: There may be color differences between aluminum plates of the same type in different batches. When selling and using different batches of paper, a color difference comparison program should be added.

鋁板安裝方向：同色鋁板安裝在同一平面上時，流向應一致，否則會產生視覺色差。

Aluminum plate installation direction: When the same colored aluminum plate is installed on the same plane, the flow direction should be consistent, otherwise it will cause visual color difference.

鋁板撕膜：鋁板安裝后45天內撕下保護膜，否則撕膜困難或發生膠轉移。

Aluminum plate film tearing: Remove the protective film from the aluminum plate within 45 days after installation, otherwise it will be difficult to tear the film or adhesive transfer may occur.

鋁板使用條件：室內墻板應在室內使用，不得安裝在室外，以保證使用效果和使用壽命。

Aluminum panel usage conditions: Indoor wall panels should be used indoors and not installed outdoors to ensure their effectiveness and lifespan.

本文由鋁板生產廠家提供技術支持，更多的詳細精彩內容請點擊我們的網站 http://www.ssstlc.com我們將會全心全意為您提供滿意的服務。

This article is supported by aluminum plate manufacturers. For more detailed and exciting content, please click on our website http://www.ssstlc.com We will wholeheartedly provide you with satisfactory service.